Filtered by vendor Linux
Subscriptions
Total
13522 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2024-44971 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: dsa: bcm_sf2: Fix a possible memory leak in bcm_sf2_mdio_register() bcm_sf2_mdio_register() calls of_phy_find_device() and then phy_device_remove() in a loop to remove existing PHY devices. of_phy_find_device() eventually calls bus_find_device(), which calls get_device() on the returned struct device * to increment the refcount. The current implementation does not decrement the refcount, which causes memory leak. This commit adds the missing phy_device_free() call to decrement the refcount via put_device() to balance the refcount. | ||||
| CVE-2024-44969 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: s390/sclp: Prevent release of buffer in I/O When a task waiting for completion of a Store Data operation is interrupted, an attempt is made to halt this operation. If this attempt fails due to a hardware or firmware problem, there is a chance that the SCLP facility might store data into buffers referenced by the original operation at a later time. Handle this situation by not releasing the referenced data buffers if the halt attempt fails. For current use cases, this might result in a leak of few pages of memory in case of a rare hardware/firmware malfunction. | ||||
| CVE-2024-44968 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: tick/broadcast: Move per CPU pointer access into the atomic section The recent fix for making the take over of the broadcast timer more reliable retrieves a per CPU pointer in preemptible context. This went unnoticed as compilers hoist the access into the non-preemptible region where the pointer is actually used. But of course it's valid that the compiler keeps it at the place where the code puts it which rightfully triggers: BUG: using smp_processor_id() in preemptible [00000000] code: caller is hotplug_cpu__broadcast_tick_pull+0x1c/0xc0 Move it to the actual usage site which is in a non-preemptible region. | ||||
| CVE-2024-44967 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: drm/mgag200: Bind I2C lifetime to DRM device Managed cleanup with devm_add_action_or_reset() will release the I2C adapter when the underlying Linux device goes away. But the connector still refers to it, so this cleanup leaves behind a stale pointer in struct drm_connector.ddc. Bind the lifetime of the I2C adapter to the connector's lifetime by using DRM's managed release. When the DRM device goes away (after the Linux device) DRM will first clean up the connector and then clean up the I2C adapter. | ||||
| CVE-2024-44966 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: binfmt_flat: Fix corruption when not offsetting data start Commit 04d82a6d0881 ("binfmt_flat: allow not offsetting data start") introduced a RISC-V specific variant of the FLAT format which does not allocate any space for the (obsolete) array of shared library pointers. However, it did not disable the code which initializes the array, resulting in the corruption of sizeof(long) bytes before the DATA segment, generally the end of the TEXT segment. Introduce MAX_SHARED_LIBS_UPDATE which depends on the state of CONFIG_BINFMT_FLAT_NO_DATA_START_OFFSET to guard the initialization of the shared library pointer region so that it will only be initialized if space is reserved for it. | ||||
| CVE-2024-44965 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: x86/mm: Fix pti_clone_pgtable() alignment assumption Guenter reported dodgy crashes on an i386-nosmp build using GCC-11 that had the form of endless traps until entry stack exhaust and then #DF from the stack guard. It turned out that pti_clone_pgtable() had alignment assumptions on the start address, notably it hard assumes start is PMD aligned. This is true on x86_64, but very much not true on i386. These assumptions can cause the end condition to malfunction, leading to a 'short' clone. Guess what happens when the user mapping has a short copy of the entry text? Use the correct increment form for addr to avoid alignment assumptions. | ||||
| CVE-2024-44964 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: idpf: fix memory leaks and crashes while performing a soft reset The second tagged commit introduced a UAF, as it removed restoring q_vector->vport pointers after reinitializating the structures. This is due to that all queue allocation functions are performed here with the new temporary vport structure and those functions rewrite the backpointers to the vport. Then, this new struct is freed and the pointers start leading to nowhere. But generally speaking, the current logic is very fragile. It claims to be more reliable when the system is low on memory, but in fact, it consumes two times more memory as at the moment of running this function, there are two vports allocated with their queues and vectors. Moreover, it claims to prevent the driver from running into "bad state", but in fact, any error during the rebuild leaves the old vport in the partially allocated state. Finally, if the interface is down when the function is called, it always allocates a new queue set, but when the user decides to enable the interface later on, vport_open() allocates them once again, IOW there's a clear memory leak here. Just don't allocate a new queue set when performing a reset, that solves crashes and memory leaks. Readd the old queue number and reopen the interface on rollback - that solves limbo states when the device is left disabled and/or without HW queues enabled. | ||||
| CVE-2024-44963 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: btrfs: do not BUG_ON() when freeing tree block after error When freeing a tree block, at btrfs_free_tree_block(), if we fail to create a delayed reference we don't deal with the error and just do a BUG_ON(). The error most likely to happen is -ENOMEM, and we have a comment mentioning that only -ENOMEM can happen, but that is not true, because in case qgroups are enabled any error returned from btrfs_qgroup_trace_extent_post() (can be -EUCLEAN or anything returned from btrfs_search_slot() for example) can be propagated back to btrfs_free_tree_block(). So stop doing a BUG_ON() and return the error to the callers and make them abort the transaction to prevent leaking space. Syzbot was triggering this, likely due to memory allocation failure injection. | ||||
| CVE-2024-44957 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: xen: privcmd: Switch from mutex to spinlock for irqfds irqfd_wakeup() gets EPOLLHUP, when it is called by eventfd_release() by way of wake_up_poll(&ctx->wqh, EPOLLHUP), which gets called under spin_lock_irqsave(). We can't use a mutex here as it will lead to a deadlock. Fix it by switching over to a spin lock. | ||||
| CVE-2024-44956 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/xe/preempt_fence: enlarge the fence critical section It is really easy to introduce subtle deadlocks in preempt_fence_work_func() since we operate on single global ordered-wq for signalling our preempt fences behind the scenes, so even though we signal a particular fence, everything in the callback should be in the fence critical section, since blocking in the callback will prevent other published fences from signalling. If we enlarge the fence critical section to cover the entire callback, then lockdep should be able to understand this better, and complain if we grab a sensitive lock like vm->lock, which is also held when waiting on preempt fences. | ||||
| CVE-2024-44954 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: line6: Fix racy access to midibuf There can be concurrent accesses to line6 midibuf from both the URB completion callback and the rawmidi API access. This could be a cause of KMSAN warning triggered by syzkaller below (so put as reported-by here). This patch protects the midibuf call of the former code path with a spinlock for avoiding the possible races. | ||||
| CVE-2024-44953 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Fix deadlock during RTC update There is a deadlock when runtime suspend waits for the flush of RTC work, and the RTC work calls ufshcd_rpm_get_sync() to wait for runtime resume. Here is deadlock backtrace: kworker/0:1 D 4892.876354 10 10971 4859 0x4208060 0x8 10 0 120 670730152367 ptr f0ffff80c2e40000 0 1 0x00000001 0x000000ff 0x000000ff 0x000000ff <ffffffee5e71ddb0> __switch_to+0x1a8/0x2d4 <ffffffee5e71e604> __schedule+0x684/0xa98 <ffffffee5e71ea60> schedule+0x48/0xc8 <ffffffee5e725f78> schedule_timeout+0x48/0x170 <ffffffee5e71fb74> do_wait_for_common+0x108/0x1b0 <ffffffee5e71efe0> wait_for_completion+0x44/0x60 <ffffffee5d6de968> __flush_work+0x39c/0x424 <ffffffee5d6decc0> __cancel_work_sync+0xd8/0x208 <ffffffee5d6dee2c> cancel_delayed_work_sync+0x14/0x28 <ffffffee5e2551b8> __ufshcd_wl_suspend+0x19c/0x480 <ffffffee5e255fb8> ufshcd_wl_runtime_suspend+0x3c/0x1d4 <ffffffee5dffd80c> scsi_runtime_suspend+0x78/0xc8 <ffffffee5df93580> __rpm_callback+0x94/0x3e0 <ffffffee5df90b0c> rpm_suspend+0x2d4/0x65c <ffffffee5df91448> __pm_runtime_suspend+0x80/0x114 <ffffffee5dffd95c> scsi_runtime_idle+0x38/0x6c <ffffffee5df912f4> rpm_idle+0x264/0x338 <ffffffee5df90f14> __pm_runtime_idle+0x80/0x110 <ffffffee5e24ce44> ufshcd_rtc_work+0x128/0x1e4 <ffffffee5d6e3a40> process_one_work+0x26c/0x650 <ffffffee5d6e65c8> worker_thread+0x260/0x3d8 <ffffffee5d6edec8> kthread+0x110/0x134 <ffffffee5d616b18> ret_from_fork+0x10/0x20 Skip updating RTC if RPM state is not RPM_ACTIVE. | ||||
| CVE-2024-44950 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: serial: sc16is7xx: fix invalid FIFO access with special register set When enabling access to the special register set, Receiver time-out and RHR interrupts can happen. In this case, the IRQ handler will try to read from the FIFO thru the RHR register at address 0x00, but address 0x00 is mapped to DLL register, resulting in erroneous FIFO reading. Call graph example: sc16is7xx_startup(): entry sc16is7xx_ms_proc(): entry sc16is7xx_set_termios(): entry sc16is7xx_set_baud(): DLH/DLL = $009C --> access special register set sc16is7xx_port_irq() entry --> IIR is 0x0C sc16is7xx_handle_rx() entry sc16is7xx_fifo_read(): --> unable to access FIFO (RHR) because it is mapped to DLL (LCR=LCR_CONF_MODE_A) sc16is7xx_set_baud(): exit --> Restore access to general register set Fix the problem by claiming the efr_lock mutex when accessing the Special register set. | ||||
| CVE-2024-44949 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: parisc: fix a possible DMA corruption ARCH_DMA_MINALIGN was defined as 16 - this is too small - it may be possible that two unrelated 16-byte allocations share a cache line. If one of these allocations is written using DMA and the other is written using cached write, the value that was written with DMA may be corrupted. This commit changes ARCH_DMA_MINALIGN to be 128 on PA20 and 32 on PA1.1 - that's the largest possible cache line size. As different parisc microarchitectures have different cache line size, we define arch_slab_minalign(), cache_line_size() and dma_get_cache_alignment() so that the kernel may tune slab cache parameters dynamically, based on the detected cache line size. | ||||
| CVE-2024-44948 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: x86/mtrr: Check if fixed MTRRs exist before saving them MTRRs have an obsolete fixed variant for fine grained caching control of the 640K-1MB region that uses separate MSRs. This fixed variant has a separate capability bit in the MTRR capability MSR. So far all x86 CPUs which support MTRR have this separate bit set, so it went unnoticed that mtrr_save_state() does not check the capability bit before accessing the fixed MTRR MSRs. Though on a CPU that does not support the fixed MTRR capability this results in a #GP. The #GP itself is harmless because the RDMSR fault is handled gracefully, but results in a WARN_ON(). Add the missing capability check to prevent this. | ||||
| CVE-2024-44947 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: fuse: Initialize beyond-EOF page contents before setting uptodate fuse_notify_store(), unlike fuse_do_readpage(), does not enable page zeroing (because it can be used to change partial page contents). So fuse_notify_store() must be more careful to fully initialize page contents (including parts of the page that are beyond end-of-file) before marking the page uptodate. The current code can leave beyond-EOF page contents uninitialized, which makes these uninitialized page contents visible to userspace via mmap(). This is an information leak, but only affects systems which do not enable init-on-alloc (via CONFIG_INIT_ON_ALLOC_DEFAULT_ON=y or the corresponding kernel command line parameter). | ||||
| CVE-2024-44946 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: kcm: Serialise kcm_sendmsg() for the same socket. syzkaller reported UAF in kcm_release(). [0] The scenario is 1. Thread A builds a skb with MSG_MORE and sets kcm->seq_skb. 2. Thread A resumes building skb from kcm->seq_skb but is blocked by sk_stream_wait_memory() 3. Thread B calls sendmsg() concurrently, finishes building kcm->seq_skb and puts the skb to the write queue 4. Thread A faces an error and finally frees skb that is already in the write queue 5. kcm_release() does double-free the skb in the write queue When a thread is building a MSG_MORE skb, another thread must not touch it. Let's add a per-sk mutex and serialise kcm_sendmsg(). [0]: BUG: KASAN: slab-use-after-free in __skb_unlink include/linux/skbuff.h:2366 [inline] BUG: KASAN: slab-use-after-free in __skb_dequeue include/linux/skbuff.h:2385 [inline] BUG: KASAN: slab-use-after-free in __skb_queue_purge_reason include/linux/skbuff.h:3175 [inline] BUG: KASAN: slab-use-after-free in __skb_queue_purge include/linux/skbuff.h:3181 [inline] BUG: KASAN: slab-use-after-free in kcm_release+0x170/0x4c8 net/kcm/kcmsock.c:1691 Read of size 8 at addr ffff0000ced0fc80 by task syz-executor329/6167 CPU: 1 PID: 6167 Comm: syz-executor329 Tainted: G B 6.8.0-rc5-syzkaller-g9abbc24128bc #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024 Call trace: dump_backtrace+0x1b8/0x1e4 arch/arm64/kernel/stacktrace.c:291 show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:298 __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xd0/0x124 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:377 [inline] print_report+0x178/0x518 mm/kasan/report.c:488 kasan_report+0xd8/0x138 mm/kasan/report.c:601 __asan_report_load8_noabort+0x20/0x2c mm/kasan/report_generic.c:381 __skb_unlink include/linux/skbuff.h:2366 [inline] __skb_dequeue include/linux/skbuff.h:2385 [inline] __skb_queue_purge_reason include/linux/skbuff.h:3175 [inline] __skb_queue_purge include/linux/skbuff.h:3181 [inline] kcm_release+0x170/0x4c8 net/kcm/kcmsock.c:1691 __sock_release net/socket.c:659 [inline] sock_close+0xa4/0x1e8 net/socket.c:1421 __fput+0x30c/0x738 fs/file_table.c:376 ____fput+0x20/0x30 fs/file_table.c:404 task_work_run+0x230/0x2e0 kernel/task_work.c:180 exit_task_work include/linux/task_work.h:38 [inline] do_exit+0x618/0x1f64 kernel/exit.c:871 do_group_exit+0x194/0x22c kernel/exit.c:1020 get_signal+0x1500/0x15ec kernel/signal.c:2893 do_signal+0x23c/0x3b44 arch/arm64/kernel/signal.c:1249 do_notify_resume+0x74/0x1f4 arch/arm64/kernel/entry-common.c:148 exit_to_user_mode_prepare arch/arm64/kernel/entry-common.c:169 [inline] exit_to_user_mode arch/arm64/kernel/entry-common.c:178 [inline] el0_svc+0xac/0x168 arch/arm64/kernel/entry-common.c:713 el0t_64_sync_handler+0x84/0xfc arch/arm64/kernel/entry-common.c:730 el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:598 Allocated by task 6166: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x40/0x78 mm/kasan/common.c:68 kasan_save_alloc_info+0x70/0x84 mm/kasan/generic.c:626 unpoison_slab_object mm/kasan/common.c:314 [inline] __kasan_slab_alloc+0x74/0x8c mm/kasan/common.c:340 kasan_slab_alloc include/linux/kasan.h:201 [inline] slab_post_alloc_hook mm/slub.c:3813 [inline] slab_alloc_node mm/slub.c:3860 [inline] kmem_cache_alloc_node+0x204/0x4c0 mm/slub.c:3903 __alloc_skb+0x19c/0x3d8 net/core/skbuff.c:641 alloc_skb include/linux/skbuff.h:1296 [inline] kcm_sendmsg+0x1d3c/0x2124 net/kcm/kcmsock.c:783 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] sock_sendmsg+0x220/0x2c0 net/socket.c:768 splice_to_socket+0x7cc/0xd58 fs/splice.c:889 do_splice_from fs/splice.c:941 [inline] direct_splice_actor+0xec/0x1d8 fs/splice.c:1164 splice_direct_to_actor+0x438/0xa0c fs/splice.c:1108 do_splice_direct_actor ---truncated--- | ||||
| CVE-2024-44945 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nfnetlink: Initialise extack before use in ACKs Add missing extack initialisation when ACKing BATCH_BEGIN and BATCH_END. | ||||
| CVE-2024-44943 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: mm: gup: stop abusing try_grab_folio A kernel warning was reported when pinning folio in CMA memory when launching SEV virtual machine. The splat looks like: [ 464.325306] WARNING: CPU: 13 PID: 6734 at mm/gup.c:1313 __get_user_pages+0x423/0x520 [ 464.325464] CPU: 13 PID: 6734 Comm: qemu-kvm Kdump: loaded Not tainted 6.6.33+ #6 [ 464.325477] RIP: 0010:__get_user_pages+0x423/0x520 [ 464.325515] Call Trace: [ 464.325520] <TASK> [ 464.325523] ? __get_user_pages+0x423/0x520 [ 464.325528] ? __warn+0x81/0x130 [ 464.325536] ? __get_user_pages+0x423/0x520 [ 464.325541] ? report_bug+0x171/0x1a0 [ 464.325549] ? handle_bug+0x3c/0x70 [ 464.325554] ? exc_invalid_op+0x17/0x70 [ 464.325558] ? asm_exc_invalid_op+0x1a/0x20 [ 464.325567] ? __get_user_pages+0x423/0x520 [ 464.325575] __gup_longterm_locked+0x212/0x7a0 [ 464.325583] internal_get_user_pages_fast+0xfb/0x190 [ 464.325590] pin_user_pages_fast+0x47/0x60 [ 464.325598] sev_pin_memory+0xca/0x170 [kvm_amd] [ 464.325616] sev_mem_enc_register_region+0x81/0x130 [kvm_amd] Per the analysis done by yangge, when starting the SEV virtual machine, it will call pin_user_pages_fast(..., FOLL_LONGTERM, ...) to pin the memory. But the page is in CMA area, so fast GUP will fail then fallback to the slow path due to the longterm pinnalbe check in try_grab_folio(). The slow path will try to pin the pages then migrate them out of CMA area. But the slow path also uses try_grab_folio() to pin the page, it will also fail due to the same check then the above warning is triggered. In addition, the try_grab_folio() is supposed to be used in fast path and it elevates folio refcount by using add ref unless zero. We are guaranteed to have at least one stable reference in slow path, so the simple atomic add could be used. The performance difference should be trivial, but the misuse may be confusing and misleading. Redefined try_grab_folio() to try_grab_folio_fast(), and try_grab_page() to try_grab_folio(), and use them in the proper paths. This solves both the abuse and the kernel warning. The proper naming makes their usecase more clear and should prevent from abusing in the future. peterx said: : The user will see the pin fails, for gpu-slow it further triggers the WARN : right below that failure (as in the original report): : : folio = try_grab_folio(page, page_increm - 1, : foll_flags); : if (WARN_ON_ONCE(!folio)) { <------------------------ here : /* : * Release the 1st page ref if the : * folio is problematic, fail hard. : */ : gup_put_folio(page_folio(page), 1, : foll_flags); : ret = -EFAULT; : goto out; : } [1] https://lore.kernel.org/linux-mm/1719478388-31917-1-git-send-email-yangge1116@126.com/ [shy828301@gmail.com: fix implicit declaration of function try_grab_folio_fast] | ||||
| CVE-2024-44940 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: fou: remove warn in gue_gro_receive on unsupported protocol Drop the WARN_ON_ONCE inn gue_gro_receive if the encapsulated type is not known or does not have a GRO handler. Such a packet is easily constructed. Syzbot generates them and sets off this warning. Remove the warning as it is expected and not actionable. The warning was previously reduced from WARN_ON to WARN_ON_ONCE in commit 270136613bf7 ("fou: Do WARN_ON_ONCE in gue_gro_receive for bad proto callbacks"). | ||||